;.............................
;:                           :
;: HF - MACRO PROGRAMMING    :
;:...........................:
;
;-File Updated 05 Dec 1999.
;Changed Macro's 721 to 723. Removed macro 723.
;-File Updated 16 Dec 1998.
;
;This file will turn the HF Radio on or off at the main switch.
;This configuration will set the Controller up to command
;the HF radio connected to port 6.
;The Access code once HF is active will be "7" + Command.
;7 + 1, will put the HF into RX only Mode.
;7 + 1x, x = 1/USB,2/LSB,3/AM,4/FM,5/CW.
;7 + 2, Toggle between RX and TX.
;7 + 3, Exit HF Mode.
;7 + 4, Bump Down 100Hz.
;7 + xxx, xxx = Execute Command. ie. 7+7325, will give an "S" reading while in HF Mode.
;7 + 5, Select VFO A.
;7 + 5xx, xx = Memory 0-99.
;7 + 6, Bump Up 100Hz.
;7 + 7, Bump Down 500Hz.
;7 + 7x, Start Scan x = 1/Dn Slow,3/Up Slow,4/Dn Med,6/Up Med,7/Dn Fast,9/Up Fast.
;7 + 8, Recall Current VFO Settings.
;7 + 9, Bump Up 500Hz.
;7 + 0, Select VFO B.
;7 + 0xx, Write to Memory xx, xx = 0-99.
;7 + * Used as Decimal Point in Frequency, Must be used when entering a Freq.
;7 + #, Execution Key(Enter).
;7 + A, Bump Up 20Hz.
;7 + B, Bump Down 20Hz.
;
! ;Get "DTMF" prompt.
;
n050 09 0 ;Turn off Responces to Ports.
;
;Configure HF Remote.
;
n196 6 2 1 ;Configure HF for port 6, using Kenwood TS-440S.
;
;Macro 720, HF Power On.
;
n053 720 038 ;Mask responces.
n056 720 093 21 ;Turn Out-Put 2/1 On. Applies 12 volts to Radio.
n056 720 195 1 7 ;Set HF access to On, 7 for commands.
n056 720 010 721 440c0 ;Change Macro 721 to "440C0".
n056 720 010 722 ;Changes Macro 722 to "nothing".
n056 720 065 ;Unmask responces.
n056 720 167 ;Do Nothing.
n056 720 167 ;Do Nothing.
n056 720 167 ;Do Nothing.
n056 720 167 ;Do Nothing.
n056 720 167 ;Do Nothing.
n056 720 167 ;Do Nothing.
n056 720 167 ;Do Nothing.
n056 720 167 ;Do Nothing.
n056 720 167 ;Do Nothing.
n056 720 167 ;Do Nothing.
n056 720 167 ;Do Nothing.
n056 720 167 ;Do Nothing.
n056 720 198 ;Turn HF Control On.
n056 720 7 1 ;Put HF into RX mode only.
n056 720 7 3*597 ;Set Freq. to 3.597MHz. Club Net Freq.
n010 720 440c1 ;Chg Macro 720 to 440C1.
;
;Macro 721, HF Power Off.
;
n053 721 7 3 ;Turn HF command Off.
n056 721 038 ;Mask responces.
n056 721 094 21 ;Turn Out-Put 2/1 Off. Removes 12 volts from Radio.
n056 721 010 721 ;Change Macro 721 to "nothing".
n056 721 010 722 440c0 ;Change Macro 722 to "440C0".
n010 721 721 440c0 ;Chg Macro 721 to 440C0.
;
;Macro 722, HF Off Recall, Prevents repeating Macro 721.
;
n053 722 036 587 038 036 270 354 587 ;Say 'HF is OFF'.
;
;Macro 723, Delete Contents.
;
n055 723 ;
;
;Access Levels for HF Remote.
;
n190 720 5 ;Set Macro 720 to Access Level 5.
n190 721 5 ;Set Macro 722 to Access Level 5.
n190 722 7 ;Set Macro 723 to Access Level 7.
;
;Set Transmit Band Edges.
;
197 0 00 0 1*80 ;Set Low TX Limit for 160M to 1.800MHz.
197 0 00 1 1*95 ;Set High TX Limit for 160M to 1.95MHz.
197 0 01 0 3*50 ;Set Low TX Limit for 80M to 3.500MHz.
197 0 01 1 3*90 ;Set High TX Limit for 80M to 3.900MHz.
197 0 02 0 7*00 ;Set Low TX Limit for 40M to 7.000MHz.
197 0 02 1 7*10 ;Set High TX Limit for 40M to 7.100MHz.
197 0 04 0 14*050 ;Set Low Limit for 20M to 14.050MHz.
197 0 04 1 14*350 ;Set High Limit for 20M to 14.350MHz.
;Do Not Change LIMITS for 17M, 05.
197 0 06 0 21*100 ;Set Low Limit for 15M to 21.100MHz.
197 0 06 1 21*450 ;Set High Limit for 15M to 21.450MHz.
;Do Not Change LIMITS for 12M, 07.
197 0 08 0 28*000 ;Set Low Limit for 10M to 28.000MHz.
197 0 08 1 28*700 ;Set High Limit for 10M to 28.700MHz.
197 0 09 0 0*0 ;Set Low TX Limit for 6M to None. TX Disabled.
197 0 09 1 0*0 ;Set High TX Limit for 6M to None. TX Disabled.
197 0 10 0 0*0 ;Set Low TX Limit for 2M to None. TX Disabled.
197 0 10 1 0*0 ;Set High TX Limit for 2M to None. TX Disabled.
197 0 11 0 0*0 ;Set Low TX Limit for 1.25M to None. TX Disabled.
197 0 11 1 0*0 ;Set High TX Limit for 1.25M to None. TX Disabled.
197 0 12 0 0*0 ;Set Low TX Limit for 70cm to None. TX Disabled.
197 0 12 1 0*0 ;Set High TX Limit for 70cm to None. TX Disabled.
197 0 13 0 0*0 ;Set Low TX Limit for 33cm to None. TX Disabled.
197 0 13 1 0*0 ;Set High TX Limit for 33cm to None. TX Disabled.
197 0 14 0 0*0 ;Set Low TX Limit for 23cm to None. TX Disabled.
197 0 14 1 0*0 ;Set High TX Limit for 23cm to None. TX Disabled.
;
;End programming.
;