SCHEDULER

Link Communications

RLC-3 Controller

Scheduling the Scheduler

Last Update 02/18/99

The Scheduler will permit the automatic execution of any desired function on your controller. About the only limitation is your imagination. This should provide you with some ideas and sample programming on utilizing the scheduler with your RLC-3 controller. Most of this will apply to other models as well.

To download this file in text format suitable for modification or direct upload, hold the shift key and CLICK HERE

; WA8DBW/RPT RLC-3 V 1.79 Scheduler 08/14/98

; The following will configure the Scheduler to:

1. Send a special ID on the hour and half hour

2. Link to a net on 147.015 on Sunday evening at 9:00 PM

3. Link to a net on 147.27 on Mondays at 8:30 PM

4. Link to a net on 147.015 at 7:30 PM on Tuesdays

5. Link Daily to 443.200 MHz, the WA8SMQ repeater in Malvern, Ohio

; ----------------------------------------------------------------------

; Repeater ID and Information

; MACRO 671

N055 671; Delete Macro 671

N053 671 037 1 3 6 7 8; Set audio routing to ports 1, 3, 6, 7, & 8 (This sends the message to the listed ports)

; Your on the WA8DBW Repeater transmitting from 160 feet overlooking Akron Ohio, the temperature is --- degrees

N056 671 063 540 358 475 053 031 008 034 032 053 411 587 497 548 215 001 028 024 198 366 297 548 069 355 587 474 469 270 844 161

N082 00 671 00; Scheduler 00 Repeater info ID on the hour (Polite)

N082 01 671 30; Scheduler 01 Repeater info ID on half hour (Polite)

; DAILY EVENTS --------------------------------------------------------

; Note: Macros 772 and 773 are programmed to connect and disconnect port one to remote base. After a scheduled event utilizing the remote base is ended, the remote base is left disconnected from all ports but powered up and monitoring 1294.500 MHz. This may be changed to any frequency desired or eliminated. The monitoring of a port is handy if you wish to provide touch-tone access to the controller from the remote base port. If you do not want the remote to monitor for the entry of valid commands, either eliminate the line or block commands from the port. You could also program as pat of the remote base disconnect command what ever frequency you want the remote to monitor. You can enter whatever parameters you want i.e. ctcss, TX power etc.

; Connect port 1 to remote base on 443.200 Macro 680 & 681 -------------

N055 680; Erase macro 680

N056 680 036 053 031 008 049 043 047 292 507; WA8SMQ Link Up

N056 680 038; Quiet

N056 680 151 1; Radio power on

N056 680 145 0; Remote Base TX Low Power

N056 680 142 440;Go to 440 band

N056 680 152 1; Go to memory 1 (443.200 + 131.8 ED)

N056 680 772; Call macro 772 (connect port 1 and RB)

; ---------------------------------------------------------------------

; Disconnect port 1 from remote base ----------------------------------

N055 681; Erase macro 681

N056 681 036 053 031 008 049 043 047 292 171; WA8SMQ Link Down

N056 681 038; Quiet

N056 681 773; Call macro 773 (Disconnect Port 1 from Remote Base)

; ---------------------------------------------------------------------

N082 50 680 0530 0; Scheduler executes macro 680 each day at 5:30am

N082 51 681 0700 0; Scheduler executes macro 681 each day at 7:00am

; WEEKLY EVENTS --------------------------------------------------------

; ----------------------------------------------------------------------

; Sunday North Coast Net 145.290 - 110.9 ED Macro 688 & 689

; Connect Port 1 to remote base on 147.270 Macro 688 -------------------

N055 688; Erase macro 688

N056 688 036 044 033 031 048 033 336 507; NCARC Net Up

N056 688 038; Quiet

N056 688 151 1; Radio power on

N056 688 145 0; Remote Base TX Low Power

N056 688 142 1452901; Go to 145.290 -

N056 688 147 1; PL Encode On

N056 688 148 1; PL Decode On

N056 688 146 1109; Set PL to 110.9 Hz

N056 688 772; Call macro 772 (connect port 1 and RB port 2)

; ---------------------------------------------------------------------

; Disconnect port 1 from remote base Macro 689 ------------------------

N055 689; Erase macro 689

N056 689 036 044 033 031 048 033 336 171; NCARC Net Down

N056 689 038; Quiet

N056 689 145 0; Remote Base TX Low Power

N056 689 148 0; PL Decode Off

N056 689 142 12945002; Set remote base to 1294.500 MHz Simplex

N056 689 773; Call macro 773 (Disconnect Port 1 from Remote Base)

; ----------------------------------------------------------------------

; Net tonight macros ---------------------------------------------------

N055 690; erase macro

N056 690 036 044 033 031 048 033 336 490 086 009; NCARC net tonight at 9

;N082 60 691 2 0300 1; Scheduler executes macro 691 Monday @ 3pm

N056 691 063 150 396 131 336 490 086 008 021; CuyFalls RC Net tonight at 8:30

N055 692; Erase

N056 692 036 053 034 008 039 056 051 336 490 086 007 021; WD8IZU net at 7:30

N055 693; Erase

N056 693 036 041 008 056 052 336 490 086 009; K8ZV Net tonight at 9

; ------------------------------------------------------------------

N082 58 688 1 0900 1; Scheduler executes macro 688 9:00pm Sunday (1)

N082 59 689 1 0940 1; Scheduler executes macro 689 9:40pm Sunday (1)

; ----------------------------------------------------------------------

; Monday CuyahogaFalls Monday Night Net 147.27 + 110.9 ED Macro 686 & 687

; Connect port 1 to remote base on 147.270 Macro 686 ------------------

N055 686; Erase macro 686

N056 686 036 150 396 131 336 507; Cuyahoga Falls Radio Club Net Up

N056 686 038; Quiet

N056 686 151 1; Radio power on

N056 686 145 0; Remote Base TX Low Power

N056 686 142 1472703; Go to 147.270 +

N056 686 147 1; PL Encode On

N056 686 148 1; PL Decode On

N056 686 146 1109; Set PL to 110.9 Hz

N056 686 772; Call macro 772 (connect port 1 and RB)

; ---------------------------------------------------------------------

; Disconnect port 1 from remote base Macro 687 ------------------------

N055 687; Erase macro 687

N056 687 036 033 036 031 048 033 336 171; CFARC Net Down

N056 687 038; Quiet

N056 687 145 0; Remote Base TX Low Power

N056 687 148 0; PL Decode Off

N056 687 142 12945002; Set remote to 1294.500 MHz Simplex

N056 687 773; Call macro 773 (Disconnect Port 1 from Remote Base)

; ----------------------------------------------------------------------

N082 56 686 2 0830 1; Scheduler executes macro 686 8:30pm Monday (2)

N082 57 687 2 0900 1; Scheduler executes macro 687 9:00pm Monday (2)

; ----------------------------------------------------------------------

; Tuesday Swap Net on 147.015 - 110.9 E Macro 684 & 685 ----------------

; Connect port 1 to remote base on 147.015 Macro684 --------------------

N055 684; Erase macro 684

N056 684 036 053 034 008 039 541 051 336 507; WD8IZU Net Up

N056 684 038; Quiet

N056 684 151 1; Radio power on

N056 684 145 0; Remote Base TX Low Power

N056 684 142 1470153; Go to 147.015 +

N056 684 147 1; PL Encode On

N056 684 148 0; PL Decode Off

N056 684 146 1109; Set PL to 110.9 Hz

N056 684 772; Call macro 772 (connect port 1 and RB)

; ---------------------------------------------------------------------

; Disconnect port 1 from remote base Macro 685 ------------------------

N055 685; Erase macro 685

N056 685 036 053 034 008 039 541 051 336 171; WD8IZU Net Down

N056 685 038; Quiet

N056 685 145 0; Remote Base TX Low Power

N056 685 142 12945002; Set remote to 1294.500 MHz Simplex

N056 685 773; Call macro 773 (Disconnect Port 1 from Remote Base)

; ----------------------------------------------------------------------

N082 54 684 3 0730 1; Scheduler executes macro 684 7:30pm Tuesday (3)

N082 55 685 3 0830 1; Scheduler executes macro 685 8:30pm Tuesday (3)

; ----------------------------------------------------------------------

; Wednesday Swap Net on 146.55 SX Macro 682 & 683 ---------------------

; Connect port 1 to remote base on 146.550 Macro682 --------------------

N055 682; Erase macro 682

N056 682 036 041 008 541 514 001 022 006 005 005 336 507; K8ZV 146.55 Net Up

N056 682 038; Quiet

N056 682 151 1; Radio power on

N056 682 145 1; Remote Base TX Medium Power

N056 682 142 1465502; Go to 146.550 SX

N056 682 772; Call macro 772 (connect port 1 and RB)

; ---------------------------------------------------------------------

; Disconnect port 1 from remote base Macro 683 ------------------------

N055 683; Erase macro 683

N056 683 036 041 008 541 514 001 022 006 005 005 336 171; K8ZV 146.55 Net Down

N056 683 038; Quiet

N056 683 145 0; Remote Base TX Low Power

N056 142 12945002; Set remote base to 1294.500 MHz Simplex

N056 683 773; Call macro 773 (Disconnect Port 1 from Remote Base)

; ----------------------------------------------------------------------

N082 52 682 4 0900 1; Scheduler executes macro 682 9:00pm Wednesday (4)

N082 53 683 4 0945 1; Scheduler executes macro 683 9:45pm Wednesday (4)

; ----------------------------------------------------------------------

; FRIDAY "TGIF" at 5:00 pm to ports 1&3 --------------------------------

; MACRO 670

N055 670; Delete Macro 670

N053 670 037 13; Set audio routing to ports 1&3

N056 670 063 589 589 050 037 039 036 593; Speak Whistle "TGIF" Crowd

N082 03 670 6 0500 1; Scheduler 03 "TGIF" Fridays at 5PM

; END Scheduler SET UP

; -----------------------------------------------------------------------------

Back to RLC Getting Started

Back to Controller Stuff

Back to Repeater Stuff

HOME

Send Me Mail

HOSTED BY ifip.com

Last update 02/18/99